Juniper SRX Serisi Adsl Yapılandırması

Juniper DSL Ayarlama:

İlk olarak interface silme işlemi yapıyoruz;
delete interfaces ge-0/0/0 unit 0 family inet

DSL config işlemi başlıyor;

1-Interface pppoe olarak ayarlanır:
root# set interfaces fe-0/0/0 unit 0 encapsulation ppp-over-ether

2-DSL parametreleri girilir:
root# set interfaces pp0 unit 0 ppp-options chap default-chap-secret DslParola
root# set interfaces pp0 unit 0 ppp-options chap local-name DslKullanicidiAdi@isp
root# set interfaces pp0 unit 0 ppp-options chap passive

3-DSL 2.parametreler girilir:
root# set interfaces pp0 unit 0 pppoe-options underlying-interface fe-0/0/0.0
root# set interfaces pp0 unit 0 pppoe-options idle-timeout 0
root# set interfaces pp0 unit 0 pppoe-options auto-reconnect 3
root# set interfaces pp0 unit 0 pppoe-options client

4-Dsl 3. parametreler girilir:
root# set interfaces pp0 unit 0 family inet mtu 1492
root# set interfaces pp0 unit 0 family inet negotiate-address

5-Route edilir:
root# set routing-options static route 0.0.0.0/0 next-hop pp0.0

Sonuçlar gözlemlenir:
root> show ppp summary
Interface Session type Session phase Session flags
pp0.0 PPP Network

root> show ppp statistics
Session statistics from PPP process
Total sessions: 1
Sessions in disabled phase : 0
Sessions in establish phase : 0
Sessions in authenticate phase: 0
Sessions in network phase : 1
Bundles in pending phase : 0

root> show pppoe interfaces
pp0.0 Index 82
State: Session up, Session ID: 6,
Service name: None,
Session AC name: Vigor2000 PPPoE, Configured AC name: None,
Remote MAC address: 00:1d:aa:8b:c2:e0,
Session uptime: 17:06:31 ago,
Auto-reconnect timeout: 3 seconds, Idle timeout: Never,
Underlying interface: fe-0/0/0.0 Index 81

root> show interfaces pp0 brief
Physical interface: pp0, Enabled, Physical link is Up
Type: PPPoE, Link-level type: PPPoE, MTU: 1532, Speed: Unspecified
Device flags : Present Running
Interface flags: Point-To-Point SNMP-Traps

Logical interface pp0.0
Flags: Point-To-Point SNMP-Traps 0x0 Encapsulation: PPPoE
PPPoE:
State: SessionUp, Session ID: 6,
Session AC name: Vigor2000 PPPoE, Remote MAC address: 00:1d:aa:8b:c2:e0,
Configured AC name: None, Service name: None,
Auto-reconnect timeout: 3 seconds, Idle timeout: Never,
Underlying interface: fe-0/0/0.0 (Index 81)
Security: Zone: untrust
Allowed host-inbound traffic : dhcp tftp
inet my_dsl_address –> my_dsl_next_hop

Hakkında Korhan KÖSEOĞLU

Ayrıca Kontrol Et

Windows 7 Bootmgr image is corrupt the system cannot boot hatası

Windows 7 Kurulum CD’nizi takın. Bilgisayarınızı onarın(repair) seçeneğini seçin,sistem kurtarma seçenekleri gelir. Burada en üstte ”Başlangıç …

Bir cevap yazın

E-posta hesabınız yayımlanmayacak. Gerekli alanlar * ile işaretlenmişlerdir